Nene Valley Audio A40, P50, Phono1 Mono Blocks / Complete Analog Sys.
Listed · 363 Views
This listing has ended.
Listings Similar to Nene Valley Audio
Time Left: None
This listing has ended.
Condition | |
Payment methods | Contact seller |
Contact seller after sale to pay viaCertified check or Personal check | |
Ships from | Belton, MO, 64012 |
Ships to | United States |
Package dimensions | unspecified |
Shipping carrier | UPS |
Shipping cost | Free |
Average | Research Pricing |
Offering a complete setup from NVA, 2 40w mono blocks, 1 passive preamp, 1 phono preamp, 4m speaker cables, 2 pair of .5m rigid coax interconnects, 1m phono coax interconnects and 1 pair of 1m rigid coax interconnects.** Due to the design of the electronics you must use the passive preamp and the low capacitance cables.**
NVA has a unique design philosophy that would put many a high-end
manufacturer to shame:
- The cases are made entirely of non-magnetic materials: anodized aluminum,
wood and smoked plexiglass.
- The case sides are bonded together with structural adhesives to avoid the
magnetic contamination of steel screws.
- The circuit boards are similarly bonded to wood strips, themselves bonded to
the thick anodized aluminum case bottom.
- The output transistors, beefy 10 amp Darlingtons, are also bonded to the
case bottom, which acts as a superb heat-sink.
- No surprise. The diode bridge is also bonded to the case bottom, as are the
power supply caps.
- Internal high current wiring from the power supply is uncoated, stiff
solid-core coated copper of approximately 14 gauge. A real bus. No coating beats
even Teflon. The resulting girder-work makes any NVA kit amp a unique
proposition to look at with the lid off. However, pre-assembled amps are glued
shut to keep out the curious.
- The input selector switch, where fitted, is wired to the input RCA jacks
with teflon-coated, plated copper wire, as is the connection from selector
switch to the volume control and thence to the input on the circuit boards. A
small compromise.
- The volume control is of pure cermet type for minimal aural impact, even if
it may feel coarse to the touch. The pot's tracks are linear to achieve close
channel tracking, with a resistor added to simulate a log law.
- No attempt is made to add output compensation networks, such as an inductor
or parallel capacitor network or even fusing. Therefore, the amplifier is not
unconditionally stable, and requires low capacitance speaker cable. NVA's
LS1 is a superb choice. It has a separate positive and negative cable for
each channel to minimize capacitance, about 7pF per foot, and is made up
of seven individual silver alloy solid core conductors per cable in a black
woven sheath terminated in the new safety-inspired European Union banana plugs.
-
NVA assumes that you as the owner will read, understand and heed the
caveats regarding speaker wire and not short-circuiting the outputs, in order to
obtain truly high-end performance at a fraction of its normal cost. Remember,
the payoff is wonderful sound.
- There are NO adjustments for DC balance or output bias current
settings -- nothing to go wrong or drift with age. Nevertheless, the amplifiers
are direct-coupled, no coupling capacitors to colour the sound. All circuit
board electrolytics are bypassed by large value polystyrene caps, to
filter the supply over a wide band.
- All NVA amps are quiet -- extremely so.
No questions have been asked about this item.
Ask the seller a public question
You must log in to ask a question.
Return Policy
Return Window
Item can be returned within 7 days of receipt.
General Terms
Items must be returned in their original condition, with all included packing materials and no signs of use. Buyer assumes responsibility for all shipping return costs unless the item was not received as described.
Refunds
Buyer will receive a full refund in the original payment method less any shipping charges.