Allnic AudioHA3000usedAllnic Audio HA3000 Tube head amp for MC cartridgesA tube based amp designed for low to medium output cartridges. A pre-phonostage if you will. Two chassis design keeps noise down and signal pure. I suggest using it with cartridges that have above ...1800.00

Allnic Audio HA3000 Tube head amp for MC cartridges

Listing ID: lis96g5h Classified 
 Listed  · 320 Views

xactaudio 

member since November 2009

Xact Audio  Verified Dealer

Last 12 months
All-time438100.0%

0 Watchers

Time Left: None

This listing has ended.

Condition
9/10
Payment methods

Contact seller after sale to pay viaCertified check, Personal check or Wire Transfer

Ships fromBoise, ID, 83713
Ships toUnited States
Package dimensions16.0" × 14.0" × 16.0" (32.0 lbs.)
Shipping carrierFedEx
Shipping cost
Log in to see price
Original accessoriesBox, Manual
AverageResearch Pricing

A tube based amp designed for low to medium output cartridges. A pre-phonostage if you will. Two chassis design keeps noise down and signal pure. I suggest using it with cartridges that have above .25mv output. 
Below is a copy and paste of the Allnic website's description:

The HA-3000 is Allnic Audio’s pre-preamplifier, or “Head Amplifier”. It is an active, tube based device for amplification of low voltage signals from moving coil cartridges to allow connection of moving coil cartridges to the moving magnet inputs of a phono-stage. The HA-3000 is an active pre-preamplifier, not a “step-up transformer”.

This unit is a North American 120v model.

 The HA-3000 has the following features.

= Innovative Fixed Bias Circuit. In the HA-3000, two nuvistor 7895 tubes, the smallest vacuum tube, perform as amplifying devices. They magnify the tiniest signal in audio, the output voltage of MC cartridges, to match to the MM input of phono stages. Allnic applies its innovative, fixed bias circuit to achieve quiet and stable operation of the extremely sensitive 7895 tubes. The fixed bias circuit eliminates the subsonics so harmful to phono stagesand inherent in the characteristics of the R.I.A.A curve, which requires amplification of the lower frequencies. The fixed bias circuit applies a sustained negative DC voltage to the grid of the tubes and to the input coupling capacitors, blocking capacitor “crossover distortion”. This distortion is a common phenomenon but, unfortunately, is often neglected in pre-preamplifiers. The result of no “zero crossover distortion” is, simply, clearer and more vivid reproduction of the music.

= Very High S/N Ratio. The above mentioned characteristics of the R.I.A.A curve demand a hum-free pre-preamplifier and, therefore, a silent power supply circuit. Even one micro volt(1/1,000,000 of one volt) of hum noise (120Hz hum) in the output signal of a pre-preamplifier will result 63mV to the loud speakers. That is unacceptable, and Allnic has overcome the issue through its automatic pure vacuum tube voltage regulation circuitry. This voltage regulation circuit minimizes power supply hum noise to inaudibility.

= Extremely Wide Frequency Range. Though the HA-3000 has a single gain stage and no negative feedback, its frequency range capability extends from 15Hz to 125Khz(-3dB), revealing the full richness of the musical information on vinyl.

= Ultra Flexibility. The capability to follow an unpredictable musical signal with ease is strongly believed to be the heart of musicality for audio equipment. This ability can be indicated by square wave response at high frequencies, especially at 10Kh and the even more rarely achieved 20Khz. Exceeding these expectations, Allnic’s HA-3000 shows a response shape that is, even at 100Khz, in a word, beautiful.

= Micro-Phonic Free Tube Damping Know-how. Allnic’s Absorb-Gel® tube damping know-how culminates in the HA-3000.  In the HA-3000, an extreme version of this mechanical technology applied, reducing vibration induced noise in the sensitive tube amplification circuit to a level never before realized.

= Variable Input Load Impedances. The HA-3000 has four input load impedances: 50, 100, 200, and 500 ohms, selectable from a control on the front panel. This allows loading according to the output impedances of your MC cartridges. Furthermore, these loads are purely resistive, not the compound one of a step-up transformer, resulting in a pure and clean sound.

 Specification

= Inputs: MC (Moving Coil–unbalanced(RCA) × 1 pair = Outputs: Unbalanced(RCA) × 1 pair = Ground: Screw Type x 1 = Frequency Response Range : 15KHz to 30KHz, flat = Voltage gain : 30dB = S/N Ratio : More than -100 dB (CCIR) = Tubes: Pre-preamplifier: 2 x Nuvistor 7895 (equivalent 6CW4), Power Supply: 2 x 7233(no equivalent); 2 x 6BH6(equivalent CV 3908) = Maximum Input Voltage: 530mV (20Hz ~ 20KHz) Non-Clipping = Input Load Impedances: 50, 100, 200 and 500 Ohms selectable = Dimension and Weight(each unit): 215mm(W) 290mm(D) 115mm(H) = Weight: Pre-preamplifier unit: 2.5Kg (5.5lbs) = Weight: Power supply: 5.8Kg (12.7 lbs)

No questions have been asked about this item.

Ask the seller a public question

You must log in to ask a question.

Return Policy

Return Window

Returns are not accepted on this item.