Emotiva XPA-DR2

This is in great condition cosmetically, and electronically



Specifications

Audio Specifications (Two Differential Reference Amplifier Modules):

• Power Output (both channels driven):
  550 watts RMS, per channel, into 8 Ohms, at <0.1% THD.
  800 watts RMS, per channel, into 4 Ohms, at <0.1% THD.

• Power Bandwidth (at rated power; 8 Ohm load): 20 Hz to 20 kHz (+ / – 0.1 dB).

• Broad Band Frequency Response: 20 Hz to 50 kHz +0/-2 dB.

• THD + noise: < 0.008%; at 100 watts RMS; 1 kHz; 8 Ohms.

• Signal to Noise Ratio (8 Ohm load):
  > 120 dB; ref FTC rated power; unbalanced input (A-weighted).
  > 96 dB; ref 1 watt; unbalanced input (A-weighted).

• Minimum Recommended Load Impedance (per channel): 4 Ohms.
  (which equals one 4 Ohm load or two paralleled 8 Ohm loads).

• Damping Factor (8 Ohm load): > 500.

• Input Sensitivity (for rated power; 8 Ohm load): 2.1 V.

• Gain: 29 dB.

• Maximum Power Consumption: 1,700 watts.
  Note: The values shown refer to the amount of power the amplifier would 
  consume while playing test tones continuously, on all channels, at full power, into a load bank. Therefore they are not at all characteristic of what you would expect when playing music or the sound track from a movie. Normal audio signals are dynamic, so the amount of power they require from second to second varies widely, and the average is far lower than this. With normal content, even playing very loudly, one of our amplifiers will consume far less power than indicated in the chart, so these values should not be considered to be a circuit requirement for normal operation. 

• Input Impedance:
  33 kOhms (balanced).
  23.5 kOhms (unbalanced).

Input And Output Connections

• Input Connections:
  Unbalanced (RCA); balanced (XLR); one each, per channel, user selectable.

• Speaker Output Connections: Audiophile grade, gold plated, 5-way binding posts.

• Trigger:
  Trigger Input: 5 – 12 V (AC or DC); <10 mA input current required.
  Trigger Output: 12 VDC; can drive any load up to 120 mA.

Power Requirements

• Between 100 VAC and 250 VAC @ 50 / 60 Hz (automatically detected).

Front Panel Controls and Indicators

• Standby: push button (halo ring changes color to indicate Standby or On).

• Status LEDs: one per channel; blue.
  Status LEDs change to red to indicate a fault condition.

Rear Panel Controls

• AC Power switch: rocker switch (switches AC main power).

• Status LEDs switch: disables front panel Status LEDs and dims Standby button halo.

• Input selector switches (one per channel): 
  metal toggle switches; select between balanced and unbalanced inputs.

• Circuit Breaker: press button to reset circuit breaker.

Protection

• The XPA-DR2 is protected against excessive operating temperature, shorted speaker connections, ground faults, and other common fault conditions.

  This is available for demo at our store during regular business hours
  
  Olson’s HiFi is the friendliest Audio Video Store in Washington State
  
  We're located at 18904 Highway 99 STE P Lynnwood WA 98036
  
  Call the store to set a time to demo...
  
  206-462-5227
  
  As a small business, and due to low staffing, we require 3 business days in order to 
  
  properly package and ship your product.
  
  
  
  We have three listening areas and two Home theater Demo Rooms and we are featured dealers for...
  
  KEF, Monitor Audio, Golden Ear, Martin Logan, Premaluna, Parasound, KRELL, Innuos, Matrix Audio, Ask us about our Demo sale and Open box deals. Our regular business hours are Tuesday Through Saturday 11am to 6pm.