T+A Criterion TCD110S Factory Demos in original packaging. Gloss Macassar Ebony.

Sunny Components Inc

Tue, Wed, Thur, Fri 10.00am-6.00pm.Sat-10am-4pm Closed on Sunday and Monday.
1370 E Cypress St Ste D,E Covina CA-91724 USA
Tel: 626-966-6259. Fax: 626-966-5467. Cell: 626-975-1353.
Email: [email protected]. 
Store website: www.sunnyaudiovideo.com
Some of the finest products built in America & Europe, combined with the 
finest service and know how and expert setup from Electrical power to 
the finest Audio stands, electronics speakers turntables and streaming. 
We stock, install and configure Roon and MQA.

We have a Store Demonstration Criterion TCD 110S for sale! It is in great condition in Gloss Macassar Ebony wood finish.


T+A was first a loudspeaker manufacturer, and their products are
extraordinary. This is the largest speaker in the TCD line-up which
features transmission line bass, and D'Appolito designs for the mid and
high.
Fantastic speaker for 2 Channel audio
Speakers are heavy and shall be packed in original boxes. 
Shipped by freight only.
 Sounds great with @Hegel H-390 integrated Amplifier.

Shipping will be by Truck freight only as UPS breaks big packages.
Truck shipping is appox $400.00 On a pallet.

Full range fantastic speakers meant for medium to large rooms.

The TCD 110 S is a large, fully developed,
floor-standing transmission-line speaker with a very long line. It
reflects in an exemplary manner the basic principles behind the three
floor-standing loudspeakers of the TCD series. Each model features two
special bass drivers, two mid-range units in the D’Appolito arrangement,
and a completely new kind of super-quality dome tweeter with waveguide.
The cabinets are modified transmission line constructions. The drivers
employed are based on those fitted to our SOLITAIRE® high-end speakers.
The only differences between the three big floor-standers are their
physical cabinet dimensions and the size of the drive units employed.
The TCD 110 S is equipped with two 26 cm bass drivers, which are
perfectly matched to the cabinet and the resonance frequency of the
transmission line, and generate an incredibly deep, precise,
high-pressure bass thanks to their extremely low natural resonance. The
loudspeaker’s transient response is superb even at extreme levels; it
also has a wide dynamic range and is devoid of distortion.

The transmission-line principle offers major advantages over the bass
reflex system, but does call for extremely sophisticated design if the
speaker is to exhibit a very low bass cut-off frequency. In specific
terms, this means that the sound guide behind the bass drivers (the
transmission-line) must be very long – similar to an organ pipe –
otherwise very low frequencies cannot be generated. The natural
resonances of the line and the bass units must also be tuned accurately
to each other. These requirements can only be fulfilled if the cabinet
features a long sound guide (line), the bass drivers have very low
natural resonance, are capable of large excursions, feature an extremely
powerful magnet, and have high power handling capacity. Our
low-frequency drivers are specially developed and designed for this
extreme application, and therefore feature rigid die-cast aluminum
baskets, hard cones, long-excursion suspensions with accurate
centration, and extremely powerful magnets.

All three transmission-line models are of extremely complex
construction, and share the same basic design principles: an inner case
which consists of a large number of accurately machined individual
components, slotted and channeled into each other, and bonded under
pressure to ensure air-tight joints.

All the openings and slots for the drive units are machined in the
baffle itself, with the air-tight chambers for the mid-range units and
the Waveguide tweeter located behind the openings. Directly behind the
two bass drivers is the pressure chamber, coupled which the long, folded
sound guide which constitutes the transmission line. The line is
designed in such a way that its effective cross-section increases
towards the outlet port, providing an optimum damping effect for the
bass drivers. The inner case components are manufactured from different
thicknesses of MDF and particle board, which effect excellent
suppression and damping of structure-borne sound and resonances.

The large number of chambers and lines helps to make the cabinet
extremely rigid and stable once the sides are bonded in place. The
external side panels are up to 30 mm thick, and are bonded to the inner
case over their full area (i.e. laminated) in a separate process. This
construction makes the cabinets very heavy, as well as completely
eliminating structural sound and cabinet resonance effects.

California residents add sales tax
Credit Card and Paypal add 3.5%