Denon PMA-2000IVR Stereo integrated amplifier IMMACULATE very low hours 1st owner Price dropped

Denon PMA-2000IVR Stereo integrated amplifier in  Immaculate Condition 1st owner.
I have this Denon like 100% Brand New condition with very very low hours and never was opened.
NO SCRATCHES, NO MARKS, NO DOTS. Works Smooth.
This Denon is a much better version finished with Metal Front face and all around than the last one with plastic low budge finished.

OBS: The picture that shows inside configuration with two High-End Power Transforms is from web.
Comes with a Brand New remote control RC-858 that never was used and OEM manual,  OEM phono plug caps and a OEM Denon Add.
Features

UHC-MOS: The ultra-high-current (UHC) MOS single push-pull amplifier technology drives difficult speaker loads while preserving the delicate details of high quality recordings. This amp is capable of delivering peak current as much as 3 to 10 times that of a standard MOS-FET device, resulting in a balance between the power to drive the speakers and the ability to maintain the integrity of delicate musical nuances.

Twin Transformers: The Leakage Canceling (LC) Mounted Twin Transformers employ a large magnetic circuit with low magnetic flux density, this serves to eliminate interference caused by magnetic fields. The result is a transparent speaker output, low noise, and broad dynamic range.

Dynamic Power Circuit: High-current Schottky barrier diodes in the rectifier circuit were selected for their low noise characteristics and high speed response to provide high power support for the UHC-MOS. This combined with Denon's new large capacity block type electrolytic capacitor supplies plenty of clean current required by the speakers for the entire audible frequency range.

Divided Chassis: 1.6mm steel plates divide the chassis into six blocks, separating the two mono amplifier blocks and the preamp sections to prevent any noise from leaking into the preamp signal.

Wide Frequency Range: High end audio formats like DVD-Audio and SACD are supported by the 10Hz-100kHz frequency response of this amp.

Precision Signal Ground: Carefully placing ground points throughout the power amp stage helps to maintain clean, transparent sound by amplifying the signal under ideal conditions.

Mechanical Construction: The base of the chassis uses multiple vibration damping stages to minimize any effect power transformer or external vibration has on sound quality. The top plate and volume control are also impervious to vibration.

Inputs: There are seven inputs and the tape 1 and tape 2 sections also include outputs for recording.

Phono Equalizer: The high performance phono equalizer employs a first stage circuit in a discrete configuration with low noise FETs. A switch allows use of moving magnet or moving coil cartridges.

Record Out Selector: While listening to any source, the record output selector can send any source to both tape 1 and tape 2 for recording, so you can listen to one source and record a different source simultaneously. By selecting tape 1 as the input source while recording on tape 1, the preamp acts as a tape monitor.

Speaker Outputs: There are two pair of speaker outputs on the back panel. The two pair are wired in parallel and are simultaneously active, they can be used to power two pair of speakers or to bi-wire a single pair. The connections are gold plated binding posts that will accept bare wire, pin connectors, banana plugs, or spade connectors (they are not 5-Way binding posts because the positive and negative posts are too far apart for dual banana plugs).

Tone Controls: Rotary knobs on the front panel control bass, treble, and balance.

Source Direct: The bass, treble, and balance controls can be bypassed by engaging the source direct button.

Headphone: There is a standard (1/4") headphone jack on the left side of the front panel. When headphones are plugged in, the speaker outputs are disengaged.

Preamp Output: Stereo RCA preamp outputs allow connection to another amplifier or a powered subwoofer.

Power Amp Direct: On the back panel there is a power amp direct switch which bypasses all preamp functions of this unit (bass, treble, volume, etc). Engage this switch when a separate preamp is used with this amp. The AUX-2 input is used with the power amp direct feature and the headphone output is disabled. When any input other than AUX-2 is selected, the unit operates just as if the power amp direct function were turned off.

Remote: Like the amplifier, the remote is very basic. There is a power button, a mute button, a volume rocker button, and an input rocker button to scroll through the inputs. There are also transport functions for a Denon CD player.

Specifications

Specifications:

• Power: 80 Watts x 2 at 8 ohms, 160 Watts x 2 at 4 ohms
• Input S/N: Phono (moving magnet) 89dB, Phono (moving coil) 74dB, All other inputs 108dB
• Bass: +/- 8dB at 100Hz
• Treble: +/- 8dB at 10kHz
• Current Consumption: 6A