JBLLE14H-1 WooferusedJBL LE14H-1 Woofer for L250, 250Ti, 240Ti or SubwooferRefurbished JBL LE14H-1 Woofer for L250, 250Ti, 240Ti and Harman Citation 7.4 Subwoofer For Fosgate Audionics FS400 Subwoofer too! Original Cone and Dust Cap and Refurbished with Fresh Surround &a...350.00

JBL LE14H-1 Woofer for L250, 250Ti, 240Ti or Subwoofer

Listing ID: lisa7ihj Classified 
 Listed  · 710 Views

1 Watcher

Items from this seller

Time Left: None

This listing has ended.

Condition
8/10
Payment methods
Ships fromBen Lomond, CA, 95005
Ships toUnited States
Package dimensions17.0" × 17.0" × 8.0" (30.0 lbs.)
Shipping carrierUPS
Shipping cost
Log in to see price
AverageResearch Pricing

Refurbished JBL LE14H-1 Woofer for L250, 250Ti, 240Ti and Harman Citation 7.4 Subwoofer

For Fosgate Audionics FS400 Subwoofer too!

Original Cone and Dust Cap and Refurbished with Fresh Surround & Non-Rotting Port Screen in the back.

Ready to Go!


Fine craftsmanship is the main priority at Vintage-Stereo-Nut and has been repairing and/or refurbishing JBL transducers successful for more than two decades.


The black Aquaplas cone, 14” long-throw woofer with 5/8" displacement within 10% linearity is used primarily in the L250, 250Ti and 240Ti systems; this listing is a single from a JBL / Harman Kardon Citation THX 7.4 Subwoofer which uses the same driver.

Low Frequency Transducer: Model LE14H-1

Positive-to-red terminal with inward cone motion - otherwise 'negative pressure'

114dB / 300 watts / Nominal Impedance 8 ohm

Felted paper cone laminated with Aquaplas, cast aluminum frame, nominal 14 inch diameter, 4 inch copper voice coil, 19 lbs. magnet

This single woofer has the later heavy-duty professional input terminals with large push-to-open to connect the wires and the spring-loaded mechanisms fits 12 gauge wire, not the early 18 gauge version posts which often fail.


Refurbished by VSN

Removed Rotten Foam: Surround / Internal Disk

Cleaned: Basket & Cone

Inspected: Input Terminals / Spider

Installed: Fresh Foam Surround / Port Mesh Screen

24-Hour Burn-In with 30Hz Signal

Confirmed with Sound: Clear and Smooth

The surround is tested all the way to Xmax with a 30Hz signal to verify the voice coil does not rub. In addition to getting a new foam surround, the internal foam disk used as a screen over the magnet port has been removed and replaced with a non-rotting fine mesh screen on the exterior and under the foilcal. A Note: The original back label was missing; this is a spare in my shop.

Sadly this OEM foam disk ends up rotting away just like the surround does and in the worst case scenario the gooey mess ends up binding the voice coil at the pole piece. This has become a standard replacement on all JBL low transducers I service as a preventive measure after removing too many cones to clean up the voice coil and the gap.

Please Look at the Last Photos for the Packing and Shipping

Heavy Cardboard Cover for the Cone

Inner Box with 4X Cardboard on the Cone Side

Outer Heavy Box with 2" Solid Foam on the Bottom and Sides

No questions have been asked about this item.

Ask the seller a public question

You must log in to ask a question.

Return Policy

Return Window

Item can be returned within 7 days of receipt.

General Terms

Items must be returned in their original condition, with all included packing materials and no signs of use. Buyer assumes responsibility for all shipping return costs unless the item was not received as described.

Refunds

Buyer will receive a full refund in the original payment method less any shipping charges.

Special Conditions

If You Are Returning A Item: It must be in the same condition at the time of sale and include ALL original packing / Return Shipping will be Paid by Buyer