Audio ResearchPH-2Audio Research PH-2Audio Research PH2 Silver Face Plate New 6922 EH Gold Pins A mint condition all tubed Phono Stage from Audio Research with 3 x 6922 valves and with a rich sound. The PH2 is a Phono Pre-Ampl...999.00

Audio Research PH-2

Listing ID: lis7di61 Classified 
 Listed  · 773 Views

Audio Research
Time Left: 2 Days


Asking Price: $999.00

Buy It Now
Payment methodsPaypal-card

Contact seller after sale to pay via Certified check

Ships fromSt. Petersburg, FL, 33704
Ships toUnited States
Package dimensions19.0" × 10.25" × 5.25" (19.0 lbs.)
Shipping carrierUSPS
Shipping cost
Log in to see price
Original accessoriesBox
Agon-miniAverage Research Pricing

Audio Research PH2
Silver Face Plate
New 6922 EH Gold Pins

A mint condition all tubed Phono Stage from Audio Research with 3 x 6922 valves and with a rich sound.

The PH2 is a Phono Pre-Amplification stage intended for use with an active line-level stereo preamplifier. Fully single-ended from input to output, the PH2 uses a combination of J-FET input stage technology (for low inherent circuit noise) and class A operation vacuum-tube gain via three 6922 twin triodes. Total gain of the PH3 is 54 dB (non-adjustable). Used with typical line preamplifiers having 12 to 18 dB of gain, the PH3 is suitable for Phono Cartridges having .25 mV output or higher. Input impedance is factory-set at 47K ohms, and input capacitance at 90 pF. For optimal matching to moving-coil and moving-magnet Phono Cartridges, both input impedance and input capacitance may be adjusted via simple resistor and capacitor changes.

On the rear panel, the PH3 provides one pair of gold-plated, audiophile-grade single-ended connectors for L & R inputs, and one pair for outputs. High-quality single-ended interconnects such as Audio Research Litz Link 2 brand are strongly recommended for best sonic performance with the PH2.


Frequency response

±.15dB of RIAA, 10Hz to 60kHz; 3dB points below 0.5Hz and above 400kHz

Distortion (THD)

Less than .005% at .50V RMS 1kHz output

Noise & hum

0.1µV equivalent input noise, IHF weighted, shorted input (80 dB below 1mV 1kHz input)


54dB at 1kHz (MC & MM compatible)

Input impedance

47K ohms and 90pF Unbalanced. (Provisions for any value below 47K ohms or added input capacitance for matching certain magnetic cartridges.)

Output impedance

200 ohms Unbalanced. Recommended load 50K-100K ohms and 100pF. (10K ohms minimum and 2000pF maximum.)

Maximum inputs

60mV RMS at 1kHz (240 mV RMS at 10kHz)

Rated outputs

.50V RMS 10Hz to 60kHz, 100K ohm load (output capability is 30V RMS output at 1/2% THD at 1kHz).

Power supplies

Electronically-regulated low and high voltage supplies. Line regulation better than .01%

Tube complement

(3) 6922/E88cc dual triodes

Power requirements

100-135VAC 60Hz (200-270VAC 50/60Hz) 28 watts maximum. Line fuse 0.6A SLO BLO (0.3A SLO BLO 230V) 


19" (48 cm) W x 5.25" (13.4 cm) H (standard rack panel) x 10.25" (26 cm) D. Handles extend 1

10 lbs. (4.5 kg) Net; 19 lbs. (8.6 kg) Shipping..50" (3.8 cm) forward of front panel. Rear chassis fittings extend .75" (2.2 cm)  
Within 7 days of receipt - I will refund your money if you feel it was not accurately described, minus shipping. I am that confident you will like this receiver.

Contact me at 727-430-5558 or email to  

No questions have been asked about this item.

Ask the seller a public question

You must log in to ask a question.

Return Policy
Return Window

Item can be returned within 7 days of receipt.

General Terms

Items must be returned in their original condition, with all included packing materials and no signs of use. Buyer assumes responsibility for all shipping return costs unless the item was not received as described.


Buyer will receive a full refund in the original payment method less any shipping charges.

Seller Information


Last 12 months

Member since August 2015

Items from this seller

more from this seller →