Anthem INT-225 with mm phono New, Full Warranty

We are authorized Anthem dealers, this is factory sealed in black with full manufacturer's warranty.    PHONO PREAMPLIFIER
The phono preamplifier is suitable for moving magnet and high-output moving coil cartrdigesInput Impedance47 kΩInput Capacitance100 pFMaximum Input18 mV at 20 Hz, 140 mV at 1 kHz, 160mV at 20 kHzGain (at 1 kHz)35 dBCrosstalk (at 1 kHz)80 dBRIAA Response+/- 0.5 dB (100 Hz to 20 kHz); -1 dB (20 Hz)THD+N (at 1 kHz, 5 mV input)0.05%S/N Ratio (ref. 5 mV at 1 kHz, IEC-A filter)83 dBPREAMPLIFIERInput Impedance30 kΩ'Pre-Out' Output Impedance560 Ω'Rec-Out' Output Impedance100 ΩRated Input1.0 VrmsMaximum Input7.6 VrmsMinimum Load5 kΩRated Output (100 k1 load)1.0 VrmsMaximum Output (100 k1 load)7.6 VrmsHeadphone Output500 mW into 32 Ω at 0.03% THD+NChannel Separation (at 1 kHz)75 dBCrosstalk Between Inputs (at 1 kHz)72 dBXLR Pin ConfigurationPin 1: Ground; Pin 2: Positive; Pin 3: NegativeFrequency Response and Bandwidth20 Hz to 20 kHz (+0, -0.1 dB); 1 Hz to 170 kHz (+0, -3 dB)THD+N (at rated input and output, 80 kHz BW)0.003%IMD (CCIF at 15 kHz and 16 kHz)0.0005%S/N Ratio (A-weighted, ref 2.0 Vrms)105 dBPOWER AMPLIFIER
(per channel, continuous RMS, 20 Hz to 20 kHz, <1.0% THD)Frequency Response20 Hz to 20 kHz (+0, -0.15 dB)Bandwidth1 Hz to 200 kHz (+0, -3 dB)THD+N0.01% at 1 kHz, 0.03% at 20 kHz (100 W into 8 1)Power Bandwidth< 10 Hz to 100 kHz (+0, -3 dB, 200 W into 8 1)Slew Rate25 V/µsHeadroom1.4 dB (8 1), 2.8 dB (4 1)Damping Factor80 at 1 kHz (ref. 8 1)S/N Ratio (A-weighted, ref 225 W)105 dBCrosstalk> 57 dB (100 Hz to 10 kHz)Voltage Gain29 dBCONTROLInfra Red
Carrier Frequency38 kHz
Max. Emitter CurrentPass-through of inputTriggerInput PolarityNon-polarized
OutputPass-through of inputPOWER REQUIREMENTSImpedance8Ω4Ω# of Channels Driven1Both1Both*Short Term240 W225 W (FTC)330 W310 W*Power Consumption (8 Ω load)Maximum800 W
Typical300 WFuse Rating (Fuse is internal)Anthem serviceable onlyLow Voltage Version: In countries where the line voltage is 120V, this product operates from a single phase AC power source that supplies between 108V and 132V at a frequency of 60 Hz.High Voltage Version: In countries where the line voltage is 220V, 330V or 240V, this product operates from a single phase AC power source that supplies between 216V and 264V at a frequency of 50 or 60 Hz.DIMENSIONSWidth5-7/8 inches (14.9 cm) including feetHeightWidth 17-1/4 inches (43.8 cm)Depth18 inches (45.7 cm)Weight (Unpacked)42.6 lb (19.4 kg)ADVANCED LOAD MONITORING (ALM)

Anthem® integrated amplifiers are designed to perform flawlessly - offering stunning musicality, tonal neutrality and incredible dynamics while driving any speaker load reliably under real-world conditions! The power supply is conservatively rated and the amplifiers run cool for greater reliability, but we didn't stop there.

These amplifiers feature our ALM (Advanced Load Monitoring) circuitry which protects sensitive output devices by constantly monitoring temperature, current and voltage to ensure optimum long-term performance. ALM is totally non-invasive - it is not in the signal path and only engages in the most extreme circumstances to protect the amplifier from damage by maintaining the safe operating area of the output devices. Buyer beware however! Not all amplifier manufacturers have sophisticated load-monitoring provisions. Many have saved the added cost, leaving their output devices unprotected, choosing instead to use the amplifier's output devices as "fuses." At Anthem, ALM is just one of the ways in which our products provide owners with years of reliable service.