Music Hall mmf-11 Amazing Turntable

Music Hall MMF-11 Amazing Turntable

this is a trade in about 1 year old  in beautiful condition 
sound is amazing --with built in Speed Box Control ..
dust cover is included -- Cartridge is extra
we sell Ortofon , Dynavector , oricale -benz , Grado , Clear Audio cartridges 
The mmf-11 turntable, our flagship model, is a 2-speed belt-driven, audiophile quality turntable with many unique features. It is constructed using a four-plinth design and features two electronic-speed controlled motors driving a single flywheel. The mmf-11 comes in a high gloss black lacquer finish. The table sits on 4 maglev feet that are made of 2 magnets in opposition causing the whole assembly to 'float'. This further decouples the table from the environment.

PRODUCT HIGHLIGHTS

• Quadruple-Plinth Design


• Sorbothane Vibration Isolation


• '9cc Evolution' Carbon Fiber Tone Arm


• Adjustable Azimuth, VTA and Arm Lift


• Microprocessor-Controlled Motor Speed


• 33 1/3 & 45 rpm Change at Button Touch


• Magnetic-Levitation Adjustable Feet


• Removable Acrylic Dustcover


• Gold RCA Connectors


• 45 RPM Adapter

• Four layer plinth construction. Carbon fibre tone arm.


• 2 motors plus 1 flywheel. Completely isolated and decoupled electronic speed control motor (33/45 rpm).


• Inverted ceramic main bearing for quiet fluid operation. Non-resonant thick acrylic platter. Magnetic tip toe feet.


• Dimensions: W21.3" x D13.8" x H7.8". Weight: 66lbs.


• Dustcover included (not shown). Phono cartridge sold separately.

The Music Hall mmf-11 Turntable, the company's flagship model, is a 2-speed belt driven audiophile turntable featuring the unique quadruple-plinth construction originated by Music Hall. The distinctive design isolates the critical sound reproducing components. The platter, main bearing, tone arm and cartridge are located on the top platform while the adjustable magnetic-levitation feet, microprocessor speed control, motors, flywheel and wiring are all mounted to the bottom plinth. The motors, flywheel, and speed control are further isolated on their own vibration damped dual-plinth platform which is isolated from the upper three main plinths. Sorbothane hemispheres separate each of the three main plinths and provide additional vibration damping. The bottom plinth operates as a mass-loaded resonant sink for the entire turntable. Two motors and a flywheel are used to increase torque and speed stability. The mmf-11 comes in a high-gloss piano black lacquer finish and ships without cartridge. A large encapsulating acrylic dustcover is included.

Four-Plinth Design The lower plinth is a mass-loaded resonant sink that channels noise and vibration away from the critical sound producing components (arm, cartridge and platter) mounted on the top plinth. Three platforms are each separated by four Sorbothane hemispheres, which act as a suspension and isolation system. External phono sockets are attached to the top platform. A high quality interconnect is supplied. The Motors Two 16-volt synchronous motors connected to an electronic speed control drive a single flywheel. The use of two motors and flywheel increases torque and speed stability while reducing vibration. The electronic speed control runs the motors at 50Hz instead of 60Hz. (A 50Hz motor runs quieter than a 60Hz motor). The motors and speed control are firmly mounted to a separate platform that is connected to the bottom plinth of the turntable. The top three platforms are cut out and float next to but do not touch the motor platform, further isolating them from any possible motor vibration. Placing the motor flywheel system directly opposite the arm stops any motor vibration from entering the cartridge. Speed change from 33 1/3 to 45 rpm is done at the push of a button The Platter The belt runs round the perimeter of the 1.5" (38mm) acrylic platter. Acrylic was chosen for its superior sound quality and isolation properties. The platter sits on a quiet, inverted ceramic bearing. The Arm The tone arm is the 'Project 9cc' Evolution. This is a 9" one-piece precision tone arm with carbon fiber arm tube/headshell. Four hardened Swiss ABEC 7 spec ball races are used in an inverted bearing design. The counterweight's center of gravity is level with the stylus tip. It is decoupled from the arm and acts as a resonance damper. The arm also has adjustable azimuth and VTA, a damped arm lift and highly flexible top-grade internal wiring drawn from high purity copper.

• 


• 

6 month interest free terms available thru PayPal
Quest For Sound
2307-R Bristol Pike
Bensalem Pa 19020
215-953-9099
www.questforsound.com
[email protected]