Sunny Components Inc,
Tue, Wed, Thur, Fri 10.00am-6.00pm.Sat-10am-4pm Closed on Sunday and Monday.
1370 E Cypress St Ste D,E Covina CA-91724 USA
Tel: 626-966-6259. Fax: 626-966-5467. Cell: 626-975-1353.
Email: [email protected].
Store website: www.sunnyaudiovideo.com
of the finest products built in America & Europe, combined with the
finest service and know how and expert setup from Electrical power to
the finest Audio stands, electronics speakers turntables and streaming.
We stock, install and configure Roon and MQA.
T+A Elektroakustic M10 30th Anniversary Limited edition Mono Block Amplifiers for sale.
These are very Rare Amplifiers. They have been used Sparingly in my Personal home.
I have compared these to the A3000 and the M10 are much better, more power and refined.
Prefer shipment by freight on a pallet.
California residents add sales tax
Credit card and Paypal add 3.5% fee
Nominal Power* 8 Ohm 550 W
Nominal Power* 4 Ohm 1000 W
Peak Power* 8 Ohm 570 W
Peak Power* 4 Ohm 1070 W
High Current Mode
Up to 60 Watts pure
Class A mode
Up to 250 Watts in
Class AB mode
* Umains = 240V (230 V - Version)
* Umains = 120V (115 V - Version)
Frequency response (0 - -3dB) 1 Hz - 150 kHz
Slew rate 65 V / μs
Damping factor 4 Ohm > 115
Signal / noise ratio > 114 dB
Total harmonic distortion (5 W, 4 Ohm, 1 kHz) < 0,009 %
Cinch / RCA, XLR
3pin, XLR 4pin
Power-spply reservoir capacity 180000 μF
Power requirements 110 - 120 V / 50 - 60 Hz or 2500 W
220 - 240 V / 50 - 60 Hz
Dimensions (H x W x D) 52 x 35 x 48 cm
Weight 52 kg
alternatively in grey or
Remote control via P 10 or R-System
M 10 MONO POWER AMPLIFIER
Consistently High-End, consistently two-channel!
The V-series has found two new flagships: the M 10
mono power amplifier and the S 10 stereo power
amplifier.These sensational amplifiers are an
ingenious combination of classic "State of the Art"
valve technology, the latest transistor developments,
and extremely innovative circuit topology. We
deliberately designed an input stage incorporating
valves to ensure that their audiophile characteristics
define the amplifier's overall sound. The higher the
power of an output stage, the more difficult it is to
obtain that power using pure valve-based concepts.
In reality it is impossible to achieve extreme power
levels from a pure valve amplifier. For this reason an
obvious solution is to design modern, highly
sophisticated transistor circuits which are
responsible for the pure power amplification, and to
fine-tune these circuits to produce a perfect match
to the system as a whole. The circuit concept
exploited in the M 10 and S 10 is a completely new
development, and is so incredibly stable and refined
that we have been able to avoid the use of overall
negative feedback completely. In short: we have
exploited the advantages of valve and transistor
technology to the full, and avoided the
disadvantages!Our aim in developing the M 10 and S
10 was not just to build yet another "giant power
amp" which can deliver as much power as possible;
instead both amplifiers allow our music lovers to
choose between different modes of operation to suit
their personal taste, the loudspeakers in their system
and the power required.
Our aim in developing the M 10 and S 10 was not
just to build yet another "giant power amp" which
can deliver as much power as possible; instead both
amplifiers allow our music lovers to choose between
different modes of operation to suit their personal
taste, the loudspeakers in their system and the
In High Power mode the M 10 and S 10 are capable
of delivering huge power to large loudspeakers
where extreme levels are required, and they always
sound superb in so doing. However, if you prefer to
listen at normal volume, without ever needing such
extreme levels, then both amplifiers offer High
Current mode: in this mode the idle current is
doubled, the amplifier operate in Class A/B mode,
and generate up to 60 Watts (M 10) and 35 Watts (S
10) of power in pure Class A. It is also possible for
the M 10 to set up a genuine bi-amping
arrangement, as the M 10 features two identical
power amplifiers, each of which can feed a pair of
dedicated loudspeaker terminals. These facilities
ensure that you can fine-tune the M 10 and the S 10
to suit your loudspeakers exactly according to your
personal taste, the speakers and preferences.The M
10 and S 10 are designed to work extremely well
with a huge range of pre-amplifiers, although our P
102 valve pre-amplifier really is the perfect choice
as the front end to the M 10, as its overall design has
been developed to deliver a perfect sound experience
with the M 10 and S 10 under all circumstances. The
P 10 2 features fully balanced / symmetrical outputs
(optionally three-pole or four-pole with Trigger
voltage) and controls the entire system via the R-Link
data bus, including switching all components on and