HH Moerch D-8A Gold plated Finish With 2 arm wands
Listed · 1188 Views
13 Watchers
Items from this seller
This listing has ended.
Listings Similar to HH Moerch D-8A
Time Left: Listing Sold
This listing has ended.
Condition | |
Payment methods | Contact seller |
Contact seller after sale to pay viaCertified check or Personal check | |
Ships from | El Cajon, CA, 92020 |
Ships to | Worldwide |
Package dimensions | ?" × ?" × ?" (5.0 lbs.) |
Shipping carrier | unspecified |
Shipping cost | Specified after purchase |
Original accessories | Box |
Average | Research Pricing |
NO RESERVE AUCTION WINNER TAKES THIS ONE HOME
NOTE : NO PAYPAL, VISA MC + 4%, CA RESIDENTS +9% SALES TAX. INTERNATIONAL BIDDERS WIRE TRANSFER ONLY, If you don't agree with above terms do not bid.
On Customer consignment, a mint condition Moerch D-08A tonearm supplied with 2 each 12" Arm tubes, in original box. We installed this magnificent tonearm on a Custom PBN Audio GrooveMaster Turntable in September of 2012, it was recently replaced by a SME V12, the only arm that surpasses this one, but of course at a MUCH higher asking price.
Below from the HH Moerch Website.
While playing a record, the tonearm must be able to move both horizontally and vertically – horizontally as the cartridge moves towards the center of the record, and vertically to allow for imperfections (warps and bumps) in the record.
At very low frequencies the modulation in the record is only horizontal. If the tonearm can move too freely horizontally the low frequency motion of the stylus will be transferred to the cartridge itself, while the cantilever of the cartridge almost does not move, and thus only a weak signal is induced.
To have excellent audio reproduction at these low frequencies, the horizontal movement of the tonearm must be restricted – but to ensure perfect tracking this must be achieved without a similar restriction of the vertical movement. This “anisotropic” principle – different characteristics for different directions of movement – is the essence of the MØRCH DP-8.
The DP-8 has a flywheel shaped central body and two weights on the sides to stabilize the movement of the tonearm horizontally. Thus, as the cartridge moves towards the center of the record, it can only follow the average location of the groove. It cannot follow the modulation, which is all transferred to the cantilever. This means that all the recorded bass, even the very low end of the range, is reproduced with full amplitude and dynamics.
DP-8 with 9” PRECISION armtube. It is the two weights on each side of the heavy central body of the tonearm that provides for the majority of the effective mass (Inertial moment) for the horizontal mode of motion. The center of gravity of these weights are pointing backwards – either upwards or downwards, so that they contribute to the counterweighs at the same time as they provide for moving the center of gravity of the moveable part of the tonearm up or down.
Here the DP-8 is shown with a 12” armtube.
Model DP-8 has a unique combination of bearings: For the horizontal mode of motion a silicone damped high precision ball-bearing assembly increases the stability provided by the large housing and sideweights. For the vertical mode of motion two precision sapphire bearings are incorporated.
The vertical motion also may be damped if desired, by injecting silicone fluid into a well. Vertical damping is rarely needed for this model. It is independent of the damping of the horizontal mode of motion, and further it can be adjusted to all intermediate levels of damping.
Model DP-8 has an integrated device for adjusting the VTA while playing. Markings for "getting back" to a special setting is provided.
The feature with different weights of armtubes to optimize the tonearm for any cartridge is maintained. Thus warps will not influence the tracking force, and there will be no vertical deflection of the cantilever.
In model DP-8 the azimuth adjustment for perfect channel separation is accomplished at the pivot of one of the sapphire bearings.
Supplied in CHROME- or 24 carat GOLD finish.
The armtube plating being made without the use of magnetic materials.
Buy with the outmost confidence form a Legacy Audiogon Member with 100% Feedback EARNED over a decade of trading on this site.
Notes:
We do NOT accept paypal, PERIOD! As for why please search my postings in the forums on this topic.
International Transactions is settled by Wire Transfer ONLY !
Thanks for looking at this ad
No questions have been asked about this item.
Ask the seller a public question
You must log in to ask a question.
Return Policy
Return Window
Returns are not accepted on this item.